Disclosure: As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links, which means we earn a commission when you purchase through these links.
Installing an air compressor in a garage takes a lot of elbow grease. Especially in the case of professionals like auto mechanics in NASCAR. Air compressors allow many tools to service a car to get it ready instantly. In fact, garage workshops do the same to finish their work quickly.
Project efficiency increases with the use of an air compressor. You can do tasks like media blasting and paintwork with ease. Automation is the way to go with the proven procedure of production for profit.
To make money, you first have to invest in the best compressor for you. So, here are five things that will guide you to picking and installing the right one. Able Sales range of air compressors for sale has the right fit for your garage.
5 Factors That Affect the Design of the Installation
Cubic Feet Per Minute or Cfm
Cfm is the push of volume. Its where the power comes from. A professional would need around 9.0 cfm. There are, however, tools that require further cfm. This tool would require around 11.4 cfm.
To know the best fit for your garage, you should always allow for extra cfm on top of the overall requirement of the tools you use. Air compressors come with a lot of air-line and cords that need to be stored correctly so that they don’t get in the way of work.
Pounds Per Square Inch:
The pressure that goes out from compressors is measured in pounds per square inch. Furthermore, every air tool has a requirement for pressure. Some are high and need to be used for long durations. So, these tools need the compressors to pack more pressure.
The measure of pressure is psi. Most tools work with 90 psi. The range of tools you have will require great pressure. The compressor you want to buy should have an output of 90 psi.
Horsepower:
This is a measure of the output of motors just like cfm and psi. Horsepower is less accurate. You’ll still see it on the label but it’s dated.
Tank Volume:
This is the measure of gallons. The more tank volume, the easier it is on the motor. The tank volume is proportional to the speed of receiving air. Keep in mind that electric air compressors make a great deal of noise so be sure to choose the one that fits the job. Visit commercialaircompressor.ca for more information.
Most air compressors operate from 40dB to 100dB. Article about air compressors from BestOfTools says ‘If you have ever used or purchased an affordable air compressor, then you will know that they can be very loud during operation'.
Duty Cycle:
Don't run the compressor 24/7. Let it rest from time to time. All that work heats up the machine. Compressors with a duty cycle of 50 percent run for a half of a period. You should turn it off after that period is over.
A good air compressor has a big motor, tank and high duty cycle. This is especially true if you’re using tools like grinders and sanders. They run for a long time and consume plenty of power=.
Plumb It Up
A good compressor needs a good plumbing job. First, find a spot to put the compressor and don't be hasty with the work – it needs to be done properly. Honestly, there’s no completely foolproof plumbing plan because each case is unique.
Step by Step Directions and Guidance
Phase One
- First, you need a kit with 50 feet of hose. A flexible half-inch o.d. Puvex hose will do.Start with a hose and follow it up with a filter or dryer right away. Because condensation and oil damage the air tools. Also, the clump blasting media.
- They can also ruin a good paint job. So, a good dryer can help with these problems. It should come with setup necessities, such as a pressure gauge, regulator and shut-off valves.
- Go with two filters or driers if there are upgrades in the future. Keep it away from the air outlet. Don’t deal with corrosion, oil or debris. Tools function like new if operated properly in the way intended.
- Moisture collects in the system and passes through. So, you have to get yourself a valve. Plumbing at each leg drop protects the tools. Take the time to do this right. A lot of money goes into buying all the tools and the air compressor itself.
Phase 2
- The next thing you need to do is to make sure that the compressed air goes to the right place. Use a good hose and connect the fittings. Keep the fluency of work in mind when laying out the hose.
- Plan for the future. Imagine yourself working on projects. Do you see yourself moving around doing different tasks? Do you see any chances of tripping on pipes splayed out? Don't underestimate the limited space you have in your garage.
- Allocate space in a way that one task doesn’t affect another. A quick sketch on a piece of paper can be very helpful when planning your interior design.
- Get a tee fitting and a shutoff valve for a blasting cabinet in the future. Also, if you think that there might be painting, get an air hose reel.
A good car paint job can bring in a lot of money. And it can be done in a limited phase. And the placement of the air hose is related to the place where the shut-off valve goes. So, keep that in mind when visually managing space.
Conclusion:
There are plenty of air tools you can check out before you start plumbing. Follow a plan. The objective is to specialize tool space for simultaneous usage.
The plan should also consider the space that the compressor occupies, the hose length and all of the tools. Don’t do the plumbing with haste. This is what will determine the lifespan of your capital.
If you do the job right then you’ll maximize your efficiency and profit. However, make sure to use the tools properly and don’t wear them out with overuse.
